Question about the Macintosh Portable

[Froggy814]

Okay, Thanks!

 

[Froggy814]

I did the two diode mods. Here are some photos in case one of you wants to do it. I went to the resistor because there was a steady 5v there.

Zener Diode Mod


External SCSI Mod

 

[Froggy814]

Also, does anyone know if I can restore the original silicone rollers on the trackball? I don't like the 12 dollar price tag on the ones on ebay.

 

[Froggy814]

BlueSCSI on Macintosh Portable

I am using no special configuration (Mac Plus) and a self made adapter (some pics in the Resources section of the forum). Virtual drive formatted using HD Toolkit and with HDT driver installed. I just did a random test, waking it up 10 times in sequence after sleep. Not a single failure, even...

tinkerdifferent.com

@Sideburn
Do you remember or know what pin on the portable is 5v for the floppy drive? Can you label it? Thanks!

 

[finkmac]

Also, does anyone know if I can restore the original silicone rollers on the trackball? I don't like the 12 dollar price tag on the ones on ebay.

no.
just buy some silicone earring backs in an appropriate size.

 

[David Cook]

Also, does anyone know if I can restore the original silicone rollers on the trackball? I don't like the 12 dollar price tag on the ones on ebay.

Macintosh Portable horror story

The final conclusion of my earlier post is: TRACKBALL REPAIR SUCCESS! The tubing I ordered from this AliExpress seller ("ID 0.8mm OD 4mm") arrived last night, which enabled me to finish the repair today: I tried all kinds of nippers and other tools, but in the end, what make the straightest...

tinkerdifferent.com

 

[Froggy814]

if I put a potentiometer on one of the speaker leads would I be able to turn the sound up and down in volume or would it just not work. Or is there a way in system 6.0.8?

 

[SuperSVGA]

if I put a potentiometer on one of the speaker leads would I be able to turn the sound up and down in volume or would it just not work. Or is there a way in system 6.0.8?

Do you mean in addition to the volume control in the control panel, or is that one not working?

 

[Froggy814]

I couldn't figure out where the volume controls are. Can you maybe show me where? This is technically my first mac experience so I don't know where volume controls are.

 

[SuperSVGA]

I couldn't figure out where the volume controls are. Can you maybe show me where? This is technically my first mac experience so I don't know where volume controls are.

I believe in 6.0.8 you go to the Apple menu in the top left, Control Panel, and then the volume control I think is in both the General section and the Sound section, so you can adjust it from either location.

 

[Froggy814]

Alright, I'll try that. Thank you very much.

 

[Froggy814]

Do you have any mods for the portable you would suggest? Thanks!

 

[Froggy814]

WiFi DaynaPORT

BlueSCSI v2 Documentation

bluescsi.com

It says that I need to download their .hda to install wifi activity. How would I install the os that I want to use if they want me to use that .hda file? Wouldn't that mean that I wouldn't be able to use my .hda? I want to enable wifi activity on my portable but don't quite understand that part. Thats it. Would I be able to make my own .hda with macTCP installed then I would be able to not have to use their .hda, or is that not how it works? Thanks!

 

[Froggy814]

Do all the grounds on the video out need to be hooked up? For cable.

 

[Froggy814]

Also do I have to use all three 5v's or can I have only one?

 

[SuperSVGA]

Do all the grounds on the video out need to be hooked up? For cable.

View attachment 99014

Also do I have to use all three 5v's or can I have only one?

You could probably get by with leaving some out, but it depends on how much current you are drawing. Ideally each +5V should have a GND for current return, and then the signal lines can usually share grounds. It would probably still work with just one ground as long as there's not too much current return for the wire, but it's not recommended.

 

[Froggy814]

Alright, So still keep all the grounds and 5v rails would be what you would recommend?

 

[Froggy814]

Would I be able to have a plane for the 5V rails, or should I have them seperate?