Jump to content

ymk

6502
  • Content Count

    77
  • Joined

  • Last visited

Everything posted by ymk

  1. I've recapped many Classics and Classic IIs. The Classic especially, has many traces running underneath caps and with time, they will be eaten through. An ounce of prevention is worth a pound of cure here. I'm not asking you to send them to me, but don't run vintage hardware into the ground.
  2. Your monitor might have an "Auto" function to adjust to the signal timing.
  3. Some more options: Reset the PRAM Boot with the mouse button held down Use SCSI IDs 0 and 1
  4. For now, try swapping the HDD and CDROM SCSI IDs. Edit: If you haven't yet tried booting with the CDROM at 4 and the HDD at 0, do that first.
  5. Use the Startup control panel to set the boot device. Then you should be able to re-enable the CDROM without problems.
  6. Great! Overlap isn't happening if it's the only device. Most likely, the Mac was trying to boot from the Apple Legacy Recovery CD at SCSI ID 4.
  7. That's a good sign. On line 9 of the macsd.ini file, change the HDD SCSI ID from 5 to 0. Also add semicolons at the beginning of lines 3-7 (starting with "[4:cdrom]"). This will disable the emulated CDROM.
  8. Both resistor packs are either installed or removed. There should never be just one installed. The yellow resistors have a grey dot to mark pin 1. The DIP socket has one more pin than the resistors, so one position per row on the socket is left open. Looking at the PCB so most of the text is right-side up, pin 1 of the resistor pack is always on the edge of the DIP socket; on the left edge (labeled VCC on the PCB) for pull-up mode, or to the right edge (GND) for pull-down mode. Good, then your MacSD is probably OK.
  9. Hi Tom, I just spotted this thread. The MacSD ships with pull-up termination. To run it together with an HDD one of the following must be done: Remove the HDD's resistor packs Remove the MacSD's resistor packs (FPT termination) Change the MacSD's termination to pull-down (pin 1 in the GND column, usually needed to work with Quantum's 110 Ohm resistor packs) There is potential for damage if multiple devices are providing termination. If it turns out yours is damaged, you can send it back for repair. First, try to get the MacSD running by itse
  10. That's certainly possible. I just threw out a rough estimate. Are 80ns modules fast enough for all Macs?
  11. Somewhere in the $30 range most likely.
  12. I make these with NOS ICs. $26/ea shipped to the US. Edit: These are 256KB This same PCB accepts four ICs on the opposite side for 512K, so if there is demand, I can have them made quickly. The chips for the two module sizes have different row/column dimensions, so a 512K module cannot be made with chips from a 256K module.
  13. Nice presentation. MacSD is listed as not having floppy support. While it doesn't emulate a physical drive, it does support mounting multiple floppy images at once. I also noticed SCSI2SD is listed as having floppy support. What is the extent of floppy support on the SCSI2SD?
  14. Guessing here... to retain the memory through a battery swap.
  15. Correction: Noctua NF-R8 Redux
  16. be quiet! Pure Wings 2 80mm, BL044 Noctua NF-B9 redux I run those in my PM6100 and Centris 610 at reduced speeds and they are virtually silent. Convection cooling isn't viable for these machines. With no fan, the top of the PSU will get hot, but even a slow fan keeps it near ambient. Neat project. Would feeding TTL directly to the Mac's opposite input pin work?
  17. Video favors lower capacitance so some cables use extremely thin wires. ADB needs low resistance. Go for heavier gauge wiring or build your own cable. I would not add external power to the bus. Measure the 5v delta at the end of the chain vs at the Mac and do the same for ground.
  18. Amphenol 10127820-1422LF mates with the cable. The pins in the cable should be either 10134170 or 10127817.
×
×
  • Create New...