Jump to content

Compgeke

6502
  • Content Count

    668
  • Joined

  • Last visited

2 Followers

About Compgeke

  • Birthday 01/06/1997

Profile Information

  • Gender
    Not Telling
  • Location
    Fairfield, California

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. ATTO Cards (UL series, most commonly), Adaptec PowerDomain and OrangeMicro Grappler SCSI cards were the three most common.
  2. I'll see if I can dig up testing I did as part of my project later. I did some tests as part of current draw/voltage drop across my board by making a harness to go between the motherboard and PSU with breaks in the voltage lines. Hooked up my bench PSU as the power source to get a fairly accurate idea of current draw on 5V and 12V, as well as a measurement of input voltage vs output voltage (aka, does my board need thicker copper and/or thicker traces/more plane area?). I mostly just shat pictures into a group chat instead of actually documenting anything, which makes it difficult. Go me? I sh
  3. In a similar way, I've just straight up soldered CR2032 holders in place of the originals. Both Keystone #1058 and unknown SMT 2032 holders from Excess Solutions fit fine with the tabs directly over the original through holes. Flood through holes, glue holder in place, heat tabs. Works great.
  4. Basically any Toshiba or Plextor can. XM-5401B, PX-40TSe, etc, etc. I know Sanyo can not for sure (used in some LaCie drives). The CR504/CD600i iirc is jumperable too, using the 2nd from the far right jumper to enable 512 byte sector support. The 300i might also support that, but I don't remember off the top of my head.
  5. Does the CD emulation support 512 byte sector reads? It's an issue with real CD drives on Unix machines and not dealing with real CDs on those would be great.
  6. New Machine: Outbound 125. Got this from that ebay auction that ended last week! Not sure if it works or not yet - I need to get batteries for the keyboard.
  7. A few months ago I picked up a Mac IIci and a Mac IIsi for $40 off Craigslist. Tonight I got around to mostly finishing the IIsi . All things considered, the IIsi wasn't in the worst shape I've seen them. Some leakage, but not extreme. Power supply certainly wasn't pretty though. But what the heck, that's literally the reason I created the mAcTX. While I was in there, I also went ahead and replaced the 1/2 AA with a CR2032 and added a CPU heatsink. I've got a 50 MHz crystal to swap in eventually to overclock the machine to 25 MHz. I
  8. Came with what was once NeXTSTEP 0.9 and 1.0, but since overwritten. + one generic NeXT branded blank disk and one random third party disk. (Late post, how'd I save it instead of posting?) What's currently on them? Great question! I'm going to try and image them in a SCSI MO drive to see if I can pull something off them. Unfortunately I can't go recap and get started working on my Cube's built in drive as it's slightly burnt. I guess that's why it came completely disconnected with the interface ribbon cable missing.
  9. Came with what was once NeXTSTEP 0.9 and 1.0, but since overwritten. + one generic NeXT branded blank disk and one random third party disk. What's currently on them? Great question! I'm going to try and image them in a SCSI MO drive to see if I can pull something off them. Unfortunately I can't go recap and get started working on my Cube's built in drive as it's slightly burnt. I guess that's why it came completely disconnected with the interface ribbon cable missing.
  10. Check on these two chips specifically, the 74ALS240 s. I've had three boards where I had to replace themme to make nubus work again. They're the bus drivers for the slots, so they're reasonably important for the functionality of the slot. The bottom one usually goes first.
  11. I get enough junk I figured I should start a thread for the odds and ends I get. I'll start with today's pickup: A NeXT Cube. A friend sent me a link to one on Facebook Marketplace last night for $200, and by some miracle it was still available! It's a little beat up but shoot, the price was right. Let's ch Let's check out that motherboard. Hey! It's got a 68040! This machine's not actually marked as being a Cube but instead just a NeXT. It's been upgraded at some point. It also looks to have 8 megs of
  12. Relevant to the thread, so I'll crosspost it here
  13. Alright so use this as constructive feedback and *not* criticism of the board - I want to help avoid the mistakes I did with the mAcTX board :). So one of the first things I notice is you have the connector for the PicoPSU and the Mac harness on the same side of the board. I'd swap that Mac harness connector to the back side of the board, allowing for you to run the picopsu into the hole for the original PSU and keep the 12V lead for that going straight. The next thing I'd do is try and keep all the small parts to one side of the board, away from the middle in between
  14. Here's a sloppily trimmed and annotated version of the schematic from the mAcTX IIc. This is the setup I had to use to make soft power reliably work one everything. I've not tested this on a Q630 - but it does work on all the machines the board fits into.
×
×
  • Create New...