replacement PSU for Performa 630

[cyberish]

Hi!

what are the specs for a Performa 630 PSU? (Voltage on each output and Amperes?

I would like to replace it with something like that:

http://www.picco.nl/catalog/product_info.php/cPath/22_79/products_id/446/language/en

Would this be possible?

thx, raphael

 

[cyberish]

.... i just found this here... :

https://www.recycledgoods.com/zoom.aspx?productID=32318

resume:

+3.3 V = 4.2 A

+5 V = 9.3 A

+12 V = 2.6 A

-12 V = 0.2 A

+ 5 V (TRKL) = 0.08A

Does somebody has the PSU - connector diagram ?

 

[ojfd]

That one will blow up in seconds...

What are you trying to achieve, Raphael? Want to operate your P630 in a car or is your PSU defective?

Hi!
what are the specs for a Performa 630 PSU? (Voltage on each output and Amperes?

I would like to replace it with something like that:

http://www.picco.nl/catalog/product_info.php/cPath/22_79/products_id/446/language/en

Would this be possible?

thx, raphael

 

[Trash80toHP_Mini]

I'd think that any of the RoadApple PPC's PSUs ought to work fine in a 630.

If you want to run it in a car, get the aforementioned RoadApple PSU, an inverter of sufficient wattage and fusible links for the hookup.

For pinouts of the entire 630 - 6500 Power Connector/MoBoMedusaMess, there's a famous diagram in the CC hackin' community, but I can't remember the name.

 

[Bunsen]

That one will blow up in seconds...

Why?

i don't see full specs for that particular DC-DC PS; so, not much way of telling if it does supply enough power to each voltage - or all of the required voltages.

 

[ojfd]

Why?

1. EUR 7.75

2. http://www.picco.nl/catalog/images/A41310.jpg

That's why. It's tiny.

Follow the link prowided by OP and you will see the specs too.

 

[johnklos]

Be careful - that power supply isn't the same as the one for the Performa 630. The 630 doesn't have 3.3 volts, so putting that power supply into a 630 would likely short 5 volts and 3.3 volts together.

When putting a Performa sixtysomethingorother into a Performa 630 case, I had to cut a 5 volt line and put in my own 3.3 volt regulator. Just so you know...

 

[cyberish]

... actually the actual PSU will be dead soon I guess: the electrolyt condensators are super noisy (high frequency) which is killing my hearing.

i thaught to replace it with something quiet.

actually i put a IDE SD card reader in it too, which works now after a lot of inquiries, but not boot volume. ( i replaced the cd-rom with an old scsi hd which contains the boot partition)

i'm still interested in the specs for that PSU...

thx, raphael

 

[zuiko21]

I think those 63x-62xx have a 6-pin header on the PSU (apart from the Molex-MiniFit-Jr Power connector) for some kind of communication with the mobo, in order to power up... So, I'm afraid further research is needed for successfully powering a 630 from a "generic" PSU.

I believe that's why I can't turn on a couple of 6200 mobos on the proper wiring harness -- which is the same on the 630 Check here for some ideas (originally from http://homepage.nifty.com/frogeye/connector.html, now defunct). Those ADB Power Supply and Power-Off Command lines seem important to me.

 

[Trash80toHP_Mini]

Performa 630 = Quadra 630 = RoadApple PPC in Q630 form factor = No 3.3v on board

PSU's to avoid: Any PCI equipped Q630 form factor (6360 is the only one I know of)

 

[cyberish]

cool Zulko. I guess this brings me further...

http://homepage2.nifty.com/frogeye/connector.html#Pushwiring

The PSU connector is two rows of 7 pin. And indeed there is no 3,3 V ...