Jump to content

Search the Community

Showing results for tags 'compact'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Important Information
    • The 68kMLA Forum Rules
  • Community Connections
    • General 68kMLA News & Stuff
    • Conquests
    • Trading Post
  • Projects & Hosted Forums
    • RetroChallenge
    • 68kMLA Wiki
  • 68k Model Forums
    • Compact Mac
    • Mac II, Quadra & Centris
    • 68k LC & Performa
    • 68k PowerBook
  • PowerPC Model Forums
    • NuBus Power Mac, LC & Performa
    • PCI Power Mac & Performa
    • G3/G4/G5 Power Mac, iMac & eMac
    • PPC PowerBook & iBook
  • Everything Elseā€¦
    • Apple I, ][, /// & Lisa
    • Newton
    • Software
    • Hacks & Development
    • Peripherals

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


FACEBOOK


GOOGLEPLUS


TWITTER


YOUTUBE


Location


Interests


OCCUPATION

Found 6 results

  1. Recently imported a couple of CC ii, they both worked initially. The second one I acquired started right up, but had a "sparking" sound every time it was booted, and every time it shut down (CRT off). I noticed the fan was not working, and the back casing was not flush against the front casing. I took the back off and fitted it flush with the front, screwed it back down. Fan worked, and initially, there was that "sparking sound" but no video. Took it apart again, and this time I noticed that the grounding harness was loose, and detached from the left side bracket
  2. Hello all, The short version: The CC (re-capped) no longer boots. I seek guidance. The long version: I booted my Colour Classic earlier today after about 8 months of non-use and I ran into a series of issues. Let me start by saying that the CC has an LC 550 logic board. Both the logic board and the analogue board (integrated power supply) were fully recapped around two years ago (ceramics, tants, and electrolytics where necessary) with ONE exception. I had the wrong sized 330uf 400v, so had to resit the original (see photo). Nevertheless, the CC operated perfectly well
  3. Thought it would be better to have a separate topic so anyone finding this by search/Google could see it more easily. I installed four 9-chip, 30-pin 1MB SIMMs into my newly built Plus, and when it boots upon performing its RAM test, I get a Sad Mac code 030ff0. Googling around indicates the first byte (03) indicates a memory failure, and the latter two bytes indicate which chip failed, although since it's a set of SIMMs that isn't a terribly helpful number. I have several sets of this type of RAM laying around and I've tried different combinations and it doesn't work. Occasionally,
  4. I'm new to this forum, if I do anything outside the rules let me know and I will correct my postings as appropriate. I recently acquired an SE/30 with 8mb ram and 80mb hard drive. It is in decent physical condition, and even included an ethernet networking card. ]'> Gentleman shipped it to me, I unpacked it, plugged it in, and used it for 5 minutes. It ran great and the display was bright and sharp. Audio was fairly quiet but working (its max was about the same as my SE FDHD's mid level I suppose) I then proceed to open up the case to put in a new battery. Luckily the origin
  5. Hi, I got a hd issue with my Mac SE/30. Previously, I had totally recapped it and I replaced UE8 chip to solve a weird screen issue. Suddenly I got the blinking floppy icon at the startup. In another thread, uniserver suggested hd breakage. My SE/30 has a 40mb quantum hd. I tried to create boot floppies following this site: http://www.classic-computers.org.nz/blog/2011-12-29-disk-from-images-mac.htm but my mac only makes only strange noises and splits the discs out (dirty floppy drive??) At the moment i can't boot the system. I know mac se/30 uses SCSI 50pins, a rare standard hard to f
  6. Someone decided to put together a parts list and 3D printer files for a compact Mac based on a Raspberry Pi and Mini vMac: https://learn.adafruit.com/mini-mac-pi/ While the resolution of the screen is only 320x240, it scrolls so it can support a higher resolution. The screen is color and the emulation can support color, too. Sound and networking isn't working yet, but people can get that working with a little effort.
×
×
  • Create New...