Jump to content

epooch

6502
  • Content Count

    63
  • Joined

  • Last visited

1 Follower

Contact Methods

  • Website URL
    http://apple-crapple.blogspot.com

Profile Information

  • Gender
    Male
  • Location
    San Diego, CA

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. Hmm. You just said which made me think we were on very different pages. Anyway, good luck!
  2. NuBus Runs on a 10MHz clock, even on the II. The discussion was about a IIsi NuBus adapter. The Mac II has 4 state machines to keep the system synced up with Nubus. Maybe they are all incorporated into the IIsi NuBus adapter, but I don't see why they would be.
  3. It's open! http://www.retrochallenge.org/
  4. The SE/30's 16MHz bus speed is not right for running 10MHz NuBus. That's why the 20 MHz IIsi can do NuBus with so little hardware. You would probably need to accelerate the SE/30 to 20 MHz, and lose all of its onboard capabilities (including video and SCSI), or have a whole lot of hardware doing timing and caching. Basically another whole computer running NuBus. Maybe some card that are not timing dependent would work, but I can't think of one that wouldn't at least need a crystal change. Then your fast accelerator is running 25% slower, at best.
  5. What system is crashing? The Raspberry Pi or the Mac? What Mac/System/Browser are you using? When you are saying that outside domains are not resolving, I assume that no packets are getting through, not just that DNS isn't working (like it is a symptom, not the actual problem). Some ping tests to ip addresses would narrow down the issues. Assuming it is a routing problem, for linux PPPd, you usually need to add the options: # Enables IP forwarding on linux ktune # Add an entry for the peer to this system's ARP table. proxyarp to get everything working. This
  6. Or spray some WD-40 on the contact points (making sure to not get overspray on the drive head). Work it around, wipe down, and put on some new lithium grease. It saves the effort of having to disassemble.
  7. Sorry, that was vague. I was referring to modifying the I/O to the logic and drive controller in the 800k Drive. So the Sony's 800k drive controller would just work. Hmm, I thought the SmartPort firmware in conjunction with the IWM was used to control the Apple 3.5" drives and the 'Intelligent" 3.5 UniDisk drive. But if the Liron ROM is a sub-set of the standard Smartport firmware (which makes sense), then I agree that IIc+ or IIgs ROM code would be needed. Now I definitely think it would be easier to have a microcontroller sitting in between, translating SmartPort to 3.5" dri
  8. My thought was to half the PWM frequency and double the TACH frequency so that the 800k controller would just work. But I am sure there will be problems with jitter, etc, running it so far out of the specifications. I think I am better off just looking into a modern buffering FIFO (or even a microcontroller) that can take the place of the 65C02/RAM combination.
  9. I bought an old corroded Mac Classic Logic board to harvest the SWIM off of it. I was going to try to make my own Liron card for the Apple II, but I don't think that makes a lot of sense based on the drives it is limited to. I have a question though: It is apparent that the Apple IIe needs the Liron and 3.5" Unidisk, or the Apple II SuperDrive controller card, to read an 800K drive. Each of those solutions has its own 65C02 and RAM to be able to cache data from the drive. I though I might just be able to slow the drive down... I know the 400K drives from the Mac use PWM to control t
  10. Yes, he has one for the IIe.: http://a2heaven.com/webshop/index.php?rt=product%2Fproduct&product_id=142 out of stock though.
  11. Yes. you will probably need to install ppp on the raspberry pi though: sudo apt-get install ppp
  12. I will test it out with a bunch of short jumper wires first, then look at designing it. Regarding the jumper block - yes, I was thinking a dip switch could work well for that.
  13. I missed it! So glad someone is using ElWhip, even if it is only one person! That was a serious challenge to get the TCP/IP stack and PPP stack running in 128K. Maybe it is time to build a web browser for the Mac 128K now...
  14. Oh, if everything is in 24 bit mode, you would invert A22 instead, I think. I need to check my LC PDS NIC to see what address lines are decoded.
  15. Software: I think most of the big manufacturer's drivers are the same for Nubus / LC PDS. That would imply that the drivers can look for their ethernet card in any slot, not just LC PDS pseudo slot $E. Designing cards and Drivers for the Macintosh Family states pretty clearly that using pseudo slots would allow manufacturers to use the same driver for NuBus and PDS slots. So, I think the drivers will find the card regardless of what slot it is in and will not need to be modified. That is, if the driver would run on an SE/30 at all. Hardware:
×
×
  • Create New...