Jump to content

Search the Community

Showing results for tags 'pcmcia'.

More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


  • Important Information
    • The 68kMLA Forum Rules
  • Community Connections
    • General 68kMLA News & Stuff
    • Conquests
    • Trading Post
  • Projects & Hosted Forums
    • RetroChallenge
    • 68kMLA Wiki
  • 68k Model Forums
    • Compact Mac
    • Mac II, Quadra & Centris
    • 68k LC & Performa
    • 68k PowerBook
  • PowerPC Model Forums
    • NuBus Power Mac, LC & Performa
    • PCI Power Mac & Performa
    • G3/G4/G5 Power Mac, iMac & eMac
    • PPC PowerBook & iBook
  • Everything Elseā€¦
    • Apple I, ][, /// & Lisa
    • Newton
    • Software
    • Hacks & Development
    • Peripherals

Find results in...

Find results that contain...

Date Created

  • Start


Last Updated

  • Start


Filter by number of...


  • Start





Website URL












Found 3 results

  1. Hopefully, this would come in handy for anyone curious about the PCMCIA module made for the PowerBook 500 series. I've posted as many pictures from various angles of the board assembly and parts (in case anyone has interest in planning modifications and how much space is inside the module) as I don't intend to open this up very often. If at all. There are three hex screws, one plastic tab, and a sticker holding my Rev C module together. I didn't have a hex bit of the correct size, but a Torx T6 proved a snug fit that allowed me to remove the screws. When I depressed the plastic tab back a small distance, I was able to carefully lift and separate the pieces only slightly, hinging at the sticker in the back. Some patient "working" back and forth allowed me to carefully separate the sticker from one of the pieces, and the unit was opened. I worked the board assembly from the back to the front to lift it from the bottom molding. The module ejection mechanism is separate from the board, and is a fixture on the bottom molding - it may be difficult to replace if it becomes damaged. Here is the bottom side of the board assembly. All pieces, angled, minus screws. Left side top (from front of module). Right side top (from front of module). Left side bottom (from front of module). Right side bottom (from front of module). Overview of bottom of board. All pieces of the module. Front hinging doors of the module. There is one stretched "rubber band" that acts to spring the doors back to resting position. If this part breaks someday, you could probably just install a rubber band to replace it...I'm actually surprised this one hasn't dry-rotted, yet. Or hack another spring assembly to your fancy. Okay. Just let me know when you make USB and cardbus possible for the 500 series.
  2. td4dotnet

    Newton / Kodak picture card adapter ?

    Greetings all, Very kindly a friend of mine has dug a working Newton out of his attic and is going to hand it over this weekend (what an awesome dude!). In preparation of this momentous event I've been powering up my old hardware so that I can 'sync' with the Newton, and therefore install new software etc. I installed the connection kit for classic OS onto a G3 iMac I have in the workshop. I don't (yet) have a physical cable but maybe one will be included in the bag of goodies (fingers crossed) so I was pottering around and dug out a box of random PCMCIA cards I've collected over the years, several of which are Kodak branded Compact Flash to PCMCIA adapters. Does anyone know if these will work as a storage medium on the Newton? There are two 10mb CF 'Kodak Picture Card' modules and one 1gb lexar module which is probably not supported from what I read online... Many thanks for thoughts on this! p.s there's no Newton smiley and there should be... Mods! Mods!!
  3. Hi Folks, First post here on the forum after lurking for years, hopefully its not presumptuous leading with a request but I'm in a bit of a jam: I've purchased this Seritek 1SM2 card, looking to use it with OS9, support is described as 'limited' but present nonetheless. No luck using the re-packaged drivers from the Seritek website or on the CD it comes with. I have been in correspondence with Firmtek trying different solutions and all existing Extensions seem corrupted by OS X repackaging. I've gone through quite a few variations of dragging and dropping the 'SATAEnabler' file into the system folder. It often shows up as a nondescript PC File, or generic text document. There was one instance from one of the packages i found where the system folder recognized it and placed it into extensions, it loaded, but my card was still the generic grey box upon inserting it on reboot. On the off chance someone else out there might have them, thought i'd post this message. Any words of wisdom would be great. thanks!