Whenever i try to transfer a disk image from my host computer to the 2c, the host says the image transfer was aborted. How could i fix this?
ADT image transfer aborted
- Thread starter Macintoshguy1984
- Start date
Ok, I got to transfer a image, but the hist says there were errors. When ever i try to boot from disk, it doesn't work
The physical floppy that you're copying the image to - is it formatted?
yes, using adt
Errors wouldn't make sense when writing a floppy, then - unless there were physical defects on the disk. You're using DD/Double Density vs. HD/High Density disks, correct?
Im using dsdd
OK i tryed it again and it said it aborted again!!! But this time id did a trace!! This is what it said before it aborted...
1/20/05 3:15:29 AMSerialTransport.pushBuffer() exit.
1/20/05 3:15:29 AM CommsThread.sendPacket() calculated CRC: 0
1/20/05 3:15:29 AM CommsThread.waitForData(two bytes) entry, expecting 6 or 21
1/20/05 3:15:57 AM CommsThread.waitForData.TransportTimeoutException! (location 0)
1/20/05 3:15:57 AM CommsThread.sendPacket() timeout.
1/20/05 3:15:57 AM CommsThread.sendPacket() ACK from Apple: 15
1/20/05 3:15:57 AM CommsThread.sendPacket() didn't work; will retry #10.
1/20/05 3:15:57 AM CommsThread.sendPacket() block: 239 offset: 256.
1/20/05 3:15:57 AM CommsThread.sendPacket() backoff sleeping for 2 seconds (or 1 second, whichever is shorter).
1/20/05 3:15:58 AM CommsThread.sendPacket() exit, rc = false
1/20/05 3:15:58 AM Image transfer aborted.
1/20/05 3:15:29 AMSerialTransport.pushBuffer() exit.
1/20/05 3:15:29 AM CommsThread.sendPacket() calculated CRC: 0
1/20/05 3:15:29 AM CommsThread.waitForData(two bytes) entry, expecting 6 or 21
1/20/05 3:15:57 AM CommsThread.waitForData.TransportTimeoutException! (location 0)
1/20/05 3:15:57 AM CommsThread.sendPacket() timeout.
1/20/05 3:15:57 AM CommsThread.sendPacket() ACK from Apple: 15
1/20/05 3:15:57 AM CommsThread.sendPacket() didn't work; will retry #10.
1/20/05 3:15:57 AM CommsThread.sendPacket() block: 239 offset: 256.
1/20/05 3:15:57 AM CommsThread.sendPacket() backoff sleeping for 2 seconds (or 1 second, whichever is shorter).
1/20/05 3:15:58 AM CommsThread.sendPacket() exit, rc = false
1/20/05 3:15:58 AM Image transfer aborted.
Last edited by a moderator:
Also, after i format the disk its name will be "no name' instead of what i put.
Ok, i changed the com port rate and i got it to transfer but it said "complete - with errors!" And the disk won't boot after wards. I looked at trace and it said it transferred with 1 error but how do i find that error out?
Last edited by a moderator:
Is it possible that the floppy drives bad?
What is the name of the image, and where did you get it from so that I can download it too?
I finnaly found out it was writing all of the data as "bad blocks"
Similar threads
