3D-printed Casing for LCD Panel?
- Thread starter ktkm
- Start date
Trash80toHP_Mini
NIGHT STALKER
*(%^&$ page return continuity interruptions! 
/monthly_05_2017/post-902-0-78524900-1494714527.jpg">View attachment 12749Pic above is an enlarged hinge section with a hardwired/strain relieved axial VGA cord connection. Thought of it because the shielded ribbon cable of the original would likely prove to be unobtanium. I used to have a roll of 50 wire shielded ribbon, but it's long gone.
Lots of great reference pics of the //c original: http://www.ebay.com/itm/222374236556
I've been mulling over the notion of an adapter box for the back my pet IIfx or the back of any a Mac case. The PCB would have thru-holes for positioning the DA-15 on all four sides so the box can be built for mounting vertically or horizontally in either direction. It would have provision for hardwiring a cable with an S-Video connector to tap its power from ADB. I doubt you could run your LCD from ADB, but the proposed box would have provisions for a jack to hook in any given wall wart and provide provide lines to run power into your enclosure across unused/re-purposed lines on the shielded, round VGA cable.
The LCD cable would be hardwired with the DA-15 connections being a proper A/B switch to run a second Mac or a PC off the LCD. Dunno, still thinking it over.
/monthly_05_2017/post-902-0-78524900-1494714527.jpg">View attachment 12749Pic above is an enlarged hinge section with a hardwired/strain relieved axial VGA cord connection. Thought of it because the shielded ribbon cable of the original would likely prove to be unobtanium. I used to have a roll of 50 wire shielded ribbon, but it's long gone.
Lots of great reference pics of the //c original: http://www.ebay.com/itm/222374236556
I've been mulling over the notion of an adapter box for the back my pet IIfx or the back of any a Mac case. The PCB would have thru-holes for positioning the DA-15 on all four sides so the box can be built for mounting vertically or horizontally in either direction. It would have provision for hardwiring a cable with an S-Video connector to tap its power from ADB. I doubt you could run your LCD from ADB, but the proposed box would have provisions for a jack to hook in any given wall wart and provide provide lines to run power into your enclosure across unused/re-purposed lines on the shielded, round VGA cable.
The LCD cable would be hardwired with the DA-15 connections being a proper A/B switch to run a second Mac or a PC off the LCD. Dunno, still thinking it over.
Last edited by a moderator:
Trash80toHP_Mini
NIGHT STALKER
How's you modeling coming along?
ktkm
Well-known member
Pretty good, thanks for asking!
I actually printed a full scale model in polymer (nylon) that took 27 hours. The kick-stand and some other details had too wait (too expensive). And I have yet to make a documentation. I’ll post some pictures as soon as my vacation starts in a week.
Trash80toHP_Mini
NIGHT STALKER
Have you had a chance to get pics of your printed sections?
ktkm
Well-known member
It has been a while, and I have almost forgotten about the project. I made some wrong calculations regarding the mounting, so I have to do some filing and fiddling. The kick-stand was too advanced and expensive for me at this point, since this is my first print-out ever. But here are some pictures!
Please, tell me what you think.
Please, tell me what you think.
Trash80toHP_Mini
NIGHT STALKER
Amazing, loving it! :approve:
Last edited by a moderator:
Trash80toHP_Mini
NIGHT STALKER
It has been a while, and I have almost forgotten about the project. I made some wrong calculations regarding the mounting, so I have to do some filing and fiddling. The kick-stand was too advanced and expensive for me at this point, since this is my first print-out ever. But here are some pictures!
Please, tell me what you think.
View attachment 30236
View attachment 30237
View attachment 30238
View attachment 30239
View attachment 30240
View attachment 30241
View attachment 30242
View attachment 30243
View attachment 30244
View attachment 30245
Forgot to say FABULOUS! in the post above.
Last edited by a moderator:
ktkm
Well-known member
olePigeon
Well-known member
It's attached on the first page.
fidelware
Member
thank you Very Much
Trash80toHP_Mini
NIGHT STALKER
Has anyone done the //c LCD type base for this or any other retro case LCD unit?
My sketch doesn't show the horizontal bar the shielded ribbon cable should be running underneath in the //c pic.
I think this stand would be perfect for IIci form factor case, which is too high for using any other stand at an ergonomically correct, height/angle as I see it.
My sketch doesn't show the horizontal bar the shielded ribbon cable should be running underneath in the //c pic.
I think this stand would be perfect for IIci form factor case, which is too high for using any other stand at an ergonomically correct, height/angle as I see it.
