• Updated 2023-07-12: Hello, Guest! Welcome back, and be sure to check out this follow-up post about our outage a week or so ago.

Recent content by max1zzz

  1. M

    Macintosh IIci Logicboard recreation

    Right, I think I have maybe PM'd everyone that expressed interest but it's getting late and I have probably missed people.... If that;s you pleas PM me :)
  2. M

    Macintosh IIci Logicboard recreation

    Just came across this this again when going back through the thread, the answer is maybe. The IIci and IIsi share some customs, specifically the RBV and MDU, ignoring the NuBus controller and bus transceivers the only other custom parts not shared with the IIsi are the ADB controller (a very...
  3. M

    Macintosh IIci Logicboard recreation

    Boards have arrived and been tested! These have a couple of modifications you may be able top see: There is now a ATX connector behind the NuBus slots for people who wish to replace the original PSU, just keep in mind this will prevent most full length NuBus cards being installed in the left...
  4. M

    Tokamac build and programming XC1736 chips

    I have used my Dataman 48LV to program these successfully but as Bolle says these are not cheap. Cost me a shade over £200 iirc but you can sometimes find them much cheaper if you look around (Though keep in mind this specific model is a parallel programmer and the software only officially...
  5. M

    Nee to have a look if I have any assembled, if not I still have loads of blank PCB's and...

    Nee to have a look if I have any assembled, if not I still have loads of blank PCB's and components, drop me a PM :)
    • max1zzz
    • Profile post comment
  6. M

    Not quite yet, ned to verify this version of the PCB works, once I have done that they will be...

    Not quite yet, ned to verify this version of the PCB works, once I have done that they will be going on GitHub :)
    • max1zzz
    • Profile post comment
  7. M

    yep

    yep
    • max1zzz
    • Profile post comment
  8. M

    More new shiny things: [ATTACH]

    More new shiny things:
    • max1zzz
    • Profile post
  9. M

    Recreateing the Apple TechStep

    Unfortunately I am no longer selling these in kit form, Although I know lots of people like kits I found the ones of these I sold in kit form required allot of support during assembly and remote debugging afterwards which I just don't have the time to do. Going forward I am only going to be...
  10. M

    Well if someone wants to donate a LC PDS video card to the cause! :ROFLMAO: Adding multiple...

    Well if someone wants to donate a LC PDS video card to the cause! :ROFLMAO: Adding multiple PDS cards gets a bit more complicated as you have to handle card selection, smooshing one card and a accelerator together is much easier as the accelerator is not really a PDS card. Maybe I need to get...
    • max1zzz
    • Profile post comment
  11. M

    New shiny thing in testing: [ATTACH]

    New shiny thing in testing:
    • max1zzz
    • Profile post
  12. M

    Building PCB in Europe is soooo expensive...

    Yep. I have looked many, many times as getting PCB's produced in Europe and it;s just uneconomical for hobbiest level stuff. One IIcx board would cost me about 2-3x the total cost of 5 of them shipped from JLC last time I looked. And that's assembly Even among Chinese manufacturers JLC tends to...
  13. M

    Cloning the Farallon MacRecorder

    Wasn't me, I haven't even heard of it :)
  14. M

    Macintosh IIci Logicboard recreation

    Boards are on order! I have ordered 30 boards, all with the bottom side birdseed populated. Boards are purple with a ENIG finish The good news is that although the order as a hole was pretty expensive the per board cost is actually lower than I expected so it's looking like the final price will...
  15. M

    Revisions done, will give it one final once over tomorrow evening then send it to JLC :) [ATTACH]

    Revisions done, will give it one final once over tomorrow evening then send it to JLC :)
See more
Top