Search results

Aha! It makes sense that it's *under* the tube, in terms of me not seeing it. One question - the glove makes sense, but which parts of the tube (if any) carry high voltage when live - is it just the board at the back?

My SE/30's display is shifted over too far to the right, and I want to center it. I've searched through the forums, and I understand that I need to adjust the rings on the back on the display. As much as I'm wary of doing this due to personal risk, I also can't identify exactly what to tweak -...

I've ordered both the current and previous versions of the board, and accepted the defaults - albeit (IIRC) I had to manually enter the size as that wasn't handled correctly.

I've been fixing up an SE/30 and got to the point of repairing the floppy drive. Having replaced the eject gear and lubricated the mechanism, I now find that, from the moment I turn the power on, the drive motors spins up without ceasing while the eject mechanism repeats endlessly - until I turn...

Thanks - I tried cleaning the zebra stripes, albeit only on the top side; it wasn't clear to me that they could be removed without damage. I'm away right now, but I do need to check if the IC drivers are still available...

Progress: I hadn't swapped *all* of the caps over, only those by the power manager - with the three at the top right swapped, it now boots to the checkerboard and disk prompt! However, there's at least one issue - a vertical line just over a third of the way from the left. Separately - the...

Thanks. The new smaller caps arrived, and are installed. With a fully charged battery (verified in another Portable), I get a boot chime then either the same Sad Mac error or a blank screen. If the traces are good, is there anything else I can check?

Thanks! I dug a bit deeper: - The traces actually look OK when I buzz them out ;( I've attached an image - this is right after removing the caps (see below) and I haven't cleaned the pads up yet. - After retrying a few times, I'm getting some intermittent behaviour in terms of booting between...

I'm trying to rescue an M5126 portable which formerly wouldn't start up at all - and so the first thing I did was recap. I've tried to avoid reassembling in full until I'm sure things are working, so I've carefully reconnected (with layers of insulation!) the battery holder on top of the PCB...

I had this and it turned out to be dry joints on the yoke board.

I just built one of the replica boards: - The PALs do get quite hot normally - The RAM test doesn't check the video RAM, I think(?) This kinda looks like a failing bit (or more), but I can't understand why some stuff is drawing correctly. Ideas: - Look at the schematic and recheck the...

Thanks. What I hadn't understood is that while the Mac (it's a non-backlight M5120) comes with 2MB of memory, 1MB seems to be on the motherboard and (as you hint at) 1MB appears to be on a card I didn't realise was there ;-) Does this mean the expansions differ between the backlight and...

Thanks. I'm still kind of confused, to be honest, after looking at the SE/30 schematic. I'd assume that the Mac itself would represent one side and be terminated, but the 50 and 25 pin share the same signals. This makes it conceptually easier (say) if you have a Mac with no internal drive and a...

If I have an SE/30 with an internal SCSI drive, then the drive should have termination enabled. However, if I then add an external drive - do I have to disable the internal drive's termination and add it externally (replacing it with a terminator when the external drive is not connected), or...

I have a Mac Portable M5120 with 2MB RAM, and I'm curious to know what options there are for RAM expansion at this point. MacEffects used to sell an 8MB card (which I believe Techknight designed?) which is now out of stock, but I also think there may have been schematics on this site before the...

And… it’s alive! I ended up socketing the chips, and swapping in the VIAs got it going. Thanks again to Bolle for doing this - and also for revising the board so that the latest rev has the right footprints.

Thanks! I’ve resorted to A/B this board with a known good one;; so far the SIMM signals seem broadly similar. Otherwise, I’m starting to wonder if a bad IC could cause the chime, so I might consider disassembling the ROM…

Got past that issue - there was a *tiny* blob of solder between the vias. With that clear, I get to a boot chime - but then (with a Rominator installed) the sad rising boot chimes and Simasimac. The RAM boots in another board, the muxes (and caps!) are all new parts, I can't see any other...

Hmm - I'm actually stumped: - I think the reset pin is active low, and so *meant* to be at 5V steady state; I see it toggle on the scope after a reset - Clocks and reset are going into both the 68030 and the Glue chip What I don't see (with the scope) after hitting the reset button each time...

Hmmm - can someone talk me through the reset circuit? I notice that: - UB11 has 12V at pins 11 and 12, but pin 13 drops from 12V without the chip inserted, to ~1.6V with it present. 5V is there, too. - Pin 5 (reset) seems stuck at 5V The IC pins do seem rather corroded - could the chip(s -...