Search results

  1. jmacz

    Unlike retrobrite, the super glue will take off logos printed on the cases. It's surprising how...

    Unlike retrobrite, the super glue will take off logos printed on the cases. It's surprising how fast it works.. 30 seconds and the un-yellowed original plastic shows through. All the texture is still there so it's a light layer being removed by the glue. Not really applicable but interesting.
    • jmacz
    • Profile post comment
  2. jmacz

    If the area was already smooth, that's the end of the filling process, but if the area had some...

    If the area was already smooth, that's the end of the filling process, but if the area had some texture, I'll try (keyword here being try) to recreate the texture by knicking it with a rounded pointy object (tedious process). But note this filling only works because I usually paint the machines...
    • jmacz
    • Profile post comment
  3. jmacz

    I normally clean the area, fill it with JB Plastic Weld, let it fully cure/dry, and then use...

    I normally clean the area, fill it with JB Plastic Weld, let it fully cure/dry, and then use sandpaper (start with 120 grit, go to 240, then 400 <- I stop here as I don't want a gloss finish) to sand it to where it's completely even.
    • jmacz
    • Profile post comment
  4. jmacz

    I usually leave the little marks alone, treat it like patina. I just don't like orange level...

    I usually leave the little marks alone, treat it like patina. I just don't like orange level yellowing and cracks (for structural considerations) and big gashes, missing chunks, etc. The annoying ones are where large educational institutions carved their name/equipment # into the case, super...
    • jmacz
    • Profile post comment
  5. jmacz

    Within those 30 secs, the acidic part of the glue took off the yellowed top layer. Not sure if...

    Within those 30 secs, the acidic part of the glue took off the yellowed top layer. Not sure if I've seen this mentioned before. Note I have had IPA brighten plastics as well, but that's after scrubbing for like 5-10 minutes and only sometimes. I actually tried scrubbing with IPA to the right of...
    • jmacz
    • Profile post comment
  6. jmacz

    [ATTACH] I was supergluing a cracked corner of a case... the superglue was sitting on the case...

    I was supergluing a cracked corner of a case... the superglue was sitting on the case for about 30 secs when I wiped the excess glue off and noticed brightening. I made a test 'J' next to it, waited 30 secs, wiped it off... Hmm...
    • jmacz
    • Profile post
  7. jmacz

    Twiggy Mac Beep sound

    Both the dialog notification sound and the beep sound (when you clicked outside of the dialog) are cool. Actually like it better than the one they went with later. And nice Steve Jobs icon too!
  8. jmacz

    Fonts Before Mac (1983)

    Neat! I kinda like elefont.
  9. jmacz

    Radius Rocket Compatibility

    Agreed. Hoping people can weigh in with actual recent experience and better yet, why stuff doesn't work (if known). My guess is the population of folks with cards, using them, and checking this forum is going to be small, but I'm hoping with the new clones, that population is going to see an uptick.
  10. jmacz

    jmacz journey

    Complete overkill based on what @zigzagjoe said, but decided to just finish what I started since it was already printed. With fan and retaining clip installed. Note that the angle of the picture makes it look like the clip extends beyond the nubus connector but that is not the case. No...
  11. jmacz

    Radius Rocket Compatibility

    Ok thanks. Hopefully others who have tried this can chime in, perhaps folks with a PrecisionColor. Definitely crashes though with the 8*24 GC (with acceleration enabled).
  12. jmacz

    jmacz journey

    What's crazy is that the edge of the adapter PCB that is over the Nubus connector actually perfectly rests on top of the connector plastic (no potential of short underneath either). It's almost like @zigzagjoe saw into the future and designed it perfectly for this application. :)
  13. jmacz

    jmacz journey

    Thanks! Need to find some time. I'm looking forward to your PSU rebuild :)
  14. jmacz

    Good to call out removing the glass. The one thing to keep in mind as people do that is to be...

    Good to call out removing the glass. The one thing to keep in mind as people do that is to be very careful as you handle the glass, specifically the connections that attach to it along the edges. If those separate (and they are very delicate), you will lose rows/columns of pixels and I have not...
    • jmacz
    • Profile post comment
  15. jmacz

    Wow looks really good!

    Wow looks really good!
    • jmacz
    • Profile post comment
  16. jmacz

    jmacz journey

    Ok, will consider that, thanks!
  17. jmacz

    jmacz journey

    I need to get back to that LC III and the 840AV, but I have been distracted. @cheesestraws pointed me at a writeup that @Phipli did on upgrading his Radius Rocket 25i to a Rocket 33: https://elephantandchicken.co.uk/stuffandnonsense/?p=1609 Decided to give it a try. I didn't have any spare...
  18. jmacz

    Radius Rocket Compatibility

    You might be right. I only tried with 128MB installed. I didn't try pulling memory sticks. But now that I think about it, I think @Byrd may have mentioned that it does work if you pull memory out.
  19. jmacz

    Radius Rocket Compatibility

    Another observation. RocketShare and ZigZagJoe's NuCF Card Not a thorough test by any means but preliminary use suggests no issues using @zigzagjoe 's NuCF storage solution (in a IIfx) with RocketShare.
  20. jmacz

    Radius Rocket Compatibility

    I've been playing with a Rocket 25i (in the process of upgrading it to a 33 based on a writeup @Phipli did -- but have not done this upgrade yet) in a IIfx and had some observations, as well as some questions. RocketWare vs RocketShare on a IIfx I had asked a few questions on some threads here...
Back
Top