Search results

Thanks, it works fine ... WLAN is en1

I have a WLAN dongle but there is probably no driver for it, right?

Is there a USB WiFi dongle that has a driver for a PPC G4 with OSX 10.4 or 10.5? My MacMini has no Airport Modul but it could be that this doesn't support normal WiFi anyway ...?

" The Tool Wish I Were" do the work, the installer can now be started and work ...

Put the BlueSCSI Device on my Quadra700 also Overclock to 32Mhz and install the System from CD Rom and use it than with the Performa 475.

Macintosh Performa 475 with full 040 CPU and 128MB Ram and Mainboard set to 33Mhz CPU Clock and BlueSCSI I can not install a system 8, 7.6 or 7.5 from CD ROM or Floppy Image files, see the picture ...

... the two VRAM Simms are faulty. I resolder the Simms and all works again.

In the end it even got to the point where the ID0 of the images on the SD card with ID0 and ID1 had disappeared permanently. Everything is OK again. I measured all the connections on the SCSI bus between the two sockets and the SCSI controller chip. Everything is OK. I had problems with the...

I added the CUDA reset button S1. The problem was my two new 512kB VRAM modules from the internet that I had just bought and were suddenly no longer working. With my two old 256kB VRAM modules everything was fine again. Re-solder the 512kB modules and see if they are OK again or not...

I soldered in/replaced new tantalum capacitors instead of the normal capacitors. Since then, the computer has booted normally from a floppy disk or from BlueSCSI, but there is no video. The monitor shows a frequency that is too high, but everything remains black. I don't think it's a capacitor...

No I run the 040 CPU with 33Mhz ...

What about to change some Things onto the Mainboard see the picture ...? ... is it necessary? What happens if you don't do it?

... it worked with a lot of solder and the soldering iron. I use the overclock software already but I want it fix in hardware.

I want to desolder two resistors. I applied flux and removed the solder from the pads on both sides of the resistor using a desoldering wick and then tried to remove the resistor using hot air at 400 degrees and tweezers, but that didn't work. I thought the red glue would soften, but that wasn't...

I need help and tips. The SMD components on the performa 475 board are fixed and glued with some red glue. I want to replace components but that doesn't work even with hot air. How can I remove the red glue from components?

... my system is a Performa 475 with 128MB RAM and XC68040 CPU and BlueSCSI Desktop Version buying 2024 with two HD Images on it. HD0 with System 7.1 and then HD1 with System 7.6.1 The problem is when I use/mount the SD card with my modern macOS Computer (M4 MacMini) to add a CD image for...

I install System 8 from CD on a clean HDD Partition and update that to 8.1 ...

What is unpleasant about my Performa 475 is that restarting or shutting down doesn't work under System 8.1. The computer basically freezes and the mouse still works. Under System 7.1 it works as it should, i.e. when it restarts it restarts and when it shuts down a restart message appears, which...

Thanks ... It works, but with very large files the computer freezes and the 40MB file loaded via FTP, for example, has 0kB. With smaller files everything works fine. I was able to buy a PDS TP Ethernet card via the forum and I think I'm using that.

Yes, I use 7.1 and 7.5.3 with the Classic AppleTalk and now the SCSILINK Wifi works ...