• Updated 2023-07-12: Hello, Guest! Welcome back, and be sure to check out this follow-up post about our outage a week or so ago.

Search results

  1. I

    Powerbook G3 screen hinges

    I'll first wait for the JB Weld to cure and see if that even works. Then get a replacement for the other side.
  2. I

    Powerbook G3 screen hinges

    If it doesn't work I'll just buy some Pismo hinges and remove the wireless antennas
  3. I

    Powerbook G3 screen hinges

    I have the same issue on my Lombard. Decided to try a few layers of JBweld and see how it works.
  4. I

    PowerBook G3 Lombard power problems

    Update- new display housing obtained for cheap and found a cheap original m4402 power supply- wondering if it's dangerous since I heard those had recalls
  5. I

    Solid drive light on Unidisk 5 1/4 drive, not able to read disks.

    Same issue. The motor constantly runs with no disk inserted.
  6. I

    Solid drive light on Unidisk 5 1/4 drive, not able to read disks.

    I do not know how to check speed.
  7. I

    Solid drive light on Unidisk 5 1/4 drive, not able to read disks.

    I have cleaned the heads on both drives.
  8. I

    Solid drive light on Unidisk 5 1/4 drive, not able to read disks.

    Apple iie. Controller card works with my Floppy Emu.
  9. I

    Solid drive light on Unidisk 5 1/4 drive, not able to read disks.

    My Apple Unidisk 5 1/4 disk drives doesn't read disks. Drive lights stay solid on both drives.
  10. I

    Help with OS 9 on late 2002 iBook 800mhz

    LG CRN-8245B
  11. I

    Help with OS 9 on late 2002 iBook 800mhz

    No, I don't. I did get it to boot again after a pram reset and os 9 works now.
  12. I

    Help with OS 9 on late 2002 iBook 800mhz

    Used the image from Mac OS 9 lives now it won't boot again after a restart. Won't boot holding c or option with a CD. Get an error in single user mode.
  13. I

    Power Mac g4 Quicksilver 867MHZ single dead after thermal paste install.

    Got the original CPU working again with a reflow.
  14. I

    Power Mac g4 Quicksilver 867MHZ single dead after thermal paste install.

    I have $20, so I can get the 867 from DV Warehouse.
  15. I

    Power Mac g4 Quicksilver 867MHZ single dead after thermal paste install.

    Yes. It would
  16. I

    Power Mac g4 Quicksilver 867MHZ single dead after thermal paste install.

    Problem is I don't have any money for an upgrade card. I do have money for a CPU replacement of the same type. I've read MDD cpus don't work on the quicksilver anyway. Is DV Warehouse good...
  17. I

    Power Mac g4 Quicksilver 867MHZ single dead after thermal paste install.

    I recently re did the thermal paste in my power mac g4. It was completely dead after re installing the heat sink (I used a respectable brand of non conductive thermal paste. I just reflowed the CPU today after letting it sit for months. If all else fails I will try and find a replacement CPU...
  18. I

    PowerBook G3 Lombard power problems

    does it need the outer metal rim? since there's a center ground on the inside pin.
  19. I

    PowerBook G3 Lombard power problems

    The pin seems too small, and I can't get it to fit even with more bend than that.
  20. I

    PowerBook G3 Lombard power problems

    I don't know if anything else works, that's the problem.
Top