I found an LC (LC I) that was a bad case of battery leakage and beyond repair. The leakage was confined to one half of the logic board, however. I did my best to remove some of the healthy-looking chips.
Is anyone here is interested in them? Given their dubious history plus the thermal stress...
All true. These are fairly standard, but I expected some variation in the placement of the standoffs, and possibly the offset from the connector edge to the pins, etc.
Good work on replacing those DBs! That's what I was hoping to see after my own repair. But once the LC I arrived, I found the...
Hi all - I'm about to start a refurb on an LC (LC I). It's not here yet, but already I can see from the advance photos that the external SCSI DB25 and the video DB15 are rusted up. (The insides may be unsalvageable.. don't know yet...)
Has anyone already found replacement parts from Digikey or...
Both drives power up, spin up and level off, and almost immediately spin down if connected solely to power. I hear no seek activity at all.
ProDrive ELS, 80M and 160M capacities.
I opened the smaller one (following your eBay link's instructions: masked, windows shut, no fans etc.) and it did...
Well, I'm stumped.
I recapped a Q605 and got it to boot, got the sound back, etc. It wasn't a trouble-free recap, though, and there are multiple bodge wires now.
What I see now is that the external SCSI seems fine. I can boot from a Zip that has the termination switch 'on'. I have no other...
Looks to be ~9.1mm fully compressed. I count 47-48 windings, so rough estimate of the wire diameter would be ~0.1875mm . End-to-end length (including loops) ~15.3mm . Coil diameter ~3.2mm . I have no credible means to measure the tension it creates.
I don't see anything that small on the link I...
I am waiting for replacement ejection gears to arrive (from Italy) before I overhaul the SuperDrives in my SE. They were due two days ago, so, could be any moment now. If I get time, I'll get a head-start - take a SuperDrive out of the SE today, compare with your photos, and see if I can size...
I'd start at https://www.mcmaster.com/springs/corrosion-resistant-extension-springs-with-loop-ends/
Use a micrometer/caliper - or just a good ruler - to measure the spring length/diameter/wire gauge and start searching for a match. I'm not sure how to get the right force.. memories of high...
I was about to ask about SCSI termination power. Cool that a topic opened up about this.
Short form:
Any good references out there on the web about SCSI termination? Any ideas how a logic board can permanently damage a SCSI HDD?
Long form:
I have a logic board that seems to fry SCSI HDDs. I...
IIRC, I got the UCSD Pascal system up and running on it in my senior year of college then donated it to a high school. Probably with a (non-Super-)Serial Card and a Disk ][.
Later, I owned a //e for a while, as well as couple of IIgs systems. I had a KIM-1 for a while. There used to be "junk"...
I think Apple never meant 'normal' to include 'can be heard by everyday casual users'. I don't know dBA, really, but I'd estimate that the background noise is in the 25-30 dB range. About as loud as a whisper - and constant.
This brings me back to the topic's theme. I'd love to see some...
Just a 1+ on this locking up on a Quadra 605/System 7.5 with 36MB physical memory.
As a retired software engineer, I'd be willing to fix this. I have the sources.. but.. how do I build a new cdev/app which is compatible with the Macintosh Systems of the 1990s? I vaguely recall CodeWarrior...
And lo, there was audio.
Before I recapped the Quadra logic board, I could hear faint system noises -- continuous white noise (faint), added chatter during SCSI activity (less faint), and a number of whirrs and buzzes depending on video and ADB activity. But nothing else. No beeps, no music.
I...
So true! I checked all my new caps for shorts, in case I'd bridged their leads underneath; all good. Reseated the VRAM. No boot.
Then the battery holder arrived; I installed it and a fresh battery and the Q605 booted right up. No sound, but that was the problem that the recap was originally...
I thought the rewiring went really well. The PRAM battery clip/holder is due to arrive today but hasn't shown up, so I tried testing it without a battery.
I got nothing. No video, no sound.
On the positive side, I got no exploding caps, no smoke anywhere, no clicking/squawking power supply...
I found the perfect spot for the C36(+) bodge: the ROM SIMM socket is not populated, and very close to the RAM SIMM, and has two candidate through-holes very near C36. Now.. to craft the wires.
This is looking not-so-bad. Won't be any ugly and electrically iffy-longish rework wires running around the board edges as I feared.
Part(polarity)
Rework
C137(-)
Topside bodge to L12 near FD1.
Topside bodge to U30 pin 15.
C137(+)
Topside bodge to C136(-). *Note A
C136(+)
Topside bodge...
Thanks. I was taking a break and thinking I would continuity-check them tonight or tomorrow - but I need a board vise, third hand, aide, something.
Some of these may be "second level" challenges. C137(-)'s loss for example breaks a trace - so I expect it will require at least two bodge wires...