Recent content by Plasticoat

  1. Plasticoat

    LC II recapped but still white screen and boots in a while

    Is power supply tested and ok?
  2. Plasticoat

    Does the PSU of the Quadra 610 need recapping or is it OK?

    You are right! Your PSU needs your help now.
  3. Plasticoat

    Does the PSU of the Quadra 610 need recapping or is it OK?

    Ok, been there, someone helped me, I’m passing it on.. https://68kmla.org/bb/index.php?threads/any-one-willing-to-help-isolate-the-low-esr-on-my-map.46744/#post-522979 Also do not forget to replace the safety cap, I’m at work and do not have the info to hand, I may be able to help later 👍🏻
  4. Plasticoat

    Does the PSU of the Quadra 610 need recapping or is it OK?

    What you got in there? Dyna or Aztec? Love doing power supplies, however it’s not straight forward, caps as I am learning are not always a straight swap, some may have to be a low ESR. Anyway, you have a working PSU which is a good start, generally as a reference it’s the same PSU as a PowerPC...
  5. Plasticoat

    Philips amp chips

    Ok, a small update, the supplier from eBay was excellent, the chips I ordered came within 3 days. have replaced 2 suspect chips , with 100% success, both boards now have sound from speaker and headphone jack.
  6. Plasticoat

    Philips amp chips

    Just wanted to say thanks, I have ordered x 5 from eBay , I’ll update this thread when they arrive and have changed out the chips on the boards. I see many threads across the interweb about no sound from from speakers on LC 475’s but sound only from the headphone port, Let’s see if we can...
  7. Plasticoat

    Philips amp chips

    Hi all, not strictly a LC Performa thread, but is there a source for these chips to replace failing ones? These were used on LC’s through to later power PC’s , A link would be great If possible thanks
  8. Plasticoat

    Unsure on a safety cap

    Knew it, thanks for the confirmation 👍🏻
  9. Plasticoat

    Unsure on a safety cap

    Hi. I’m unsure on this safety cap replacement, have i ordered x when it should be y? I do not want to kill myself or anybody else 🤔 https://www.mouser.co.uk/ProductDetail/710-890324024002CS
  10. Plasticoat

    Any one willing to help isolate the low ESR on my map?

    Thanks, I really appreciate your help 👍
  11. Plasticoat

    Any one willing to help isolate the low ESR on my map?

    Would really appreciate this from someone desperately trying to avoid future probs, many thanks
  12. Plasticoat

    Recapping marathon

    If you have a map of the PSU’ s sure would appreciate a share
  13. Plasticoat

    Quicksilver needs a firmware update for Sonnet Encore ST 1.6Ghz?

    If the Mac is booting into firmware, it’s half good! If the disk is correct it should give you a series of options, 1,2,3,4 etc if your not getting those options to install remove or patch then I’d say the disk you are using is dodgy, try another installer. With good firmware. I cannot help...
  14. Plasticoat

    6100, Performa, centris Dyna Comp PSU

    Thank you for the info, I have checked other posts over the internet, and I will go ahead and replace with nothing other than quality radials. I will however, check this thread if there is any more info forthcoming . Thanks again Phipli
  15. Plasticoat

    6100, Performa, centris Dyna Comp PSU

    Hi all, I’m looking for some info on The Dyna Comp PSU, namely any Low ESR caps on the board, I have mapped and image’d, the PSU caps, but could do with the heads up. Is there a device for the future that can distinguish between low esr caps and standard radials. Thanks for looking and any...
Top