• Hello, Guest! Welcome back, and be sure to check out this post for more info about the recent service interruption and migration.

Recent content by macintosh2002

  1. M

    Pioneer D-706S CD-ROM drive

    My Pioneer Pioneer DR-706S (product-ID DR-U16S) works great with @taddy extension, thank you very much!
  2. M

    Pioneer D-706S CD-ROM drive

    My drive is spinning up too and SCSI probe recognizes the drive correctly, but without the extension and MacOS 7.5.5 it could be a problem. I´ll try it with my PM6500 or maybe G3 B&W with adaptec SCSI card and MacOS 9.
  3. M

    Pioneer D-706S CD-ROM drive

    Hello, I got a PowerMac 6100/66 with a similar Pioneer DR-706S (should be 36x speed), but without hard drive, so I´ll need that extension too, thank you for sharing, @taddy. @kkritsilas Could get your drive working with this driver? Do you have further documents / description of that Pioneer...
  4. M

    Battery bombed SE/30 - what to do with it?

    @Verault: SE/30 has a 6 layer board. @mac_enthusiast: My board looks very similar, I would say a little bit better. The only solution is Bolle's reloaded SE/30 board. Recommend the conversion, desoldering all Apple branded (RTC chip,...) components and converting to a new board. Take a look at...
  5. M

    iMac G4 700MHz Optical Drive Replacement

    I can highly recommend the optical drive from a PowerMac G5, worksgreat and fits into that place.
  6. M

    Colour Classic - screen won´t turn on

    Hello, I´ve some trouble with my Colour Classic, please let me explain. I bought this CC as not working, the seller said it won´t turn on. A few hours later when I was at home again, I tried it again and it chimed and was booting, perfect I thought. But it didn´t last long and it seems, that...
  7. M

    Sonnet Encore ZIF G4 CPU Upgrade - G3 B&W jumper setting

    I got an answer from Sonnet, but they makes it very easy for itself - they refer to the support page with the reference material 😒 @macuserman That´s nice, could you please also check your computer at home please to be sure? Your picture shows the following setting for the Sonnet ZIF G4 with...
  8. M

    Sonnet Encore ZIF G4 CPU Upgrade - G3 B&W jumper setting

    But in that manual they also mention a replacement jumper block. I made a request, hope that Sonnet will reply.
  9. M

    Sonnet Encore ZIF G4 CPU Upgrade - G3 B&W jumper setting

    Thank you for your reply. Which setting has the different jumper block for the G4 1GHz model to use it in a B&W or Yikes? The Sonnet instructions are not helpful in this point...
  10. M

    Sonnet Encore ZIF G4 CPU Upgrade - G3 B&W jumper setting

    Hello, could someone let me know how to set the jumper for a Sonnet Encore ZIF G4 1Ghz CPU in a G3 B&W? I pulled the jumper and these little metal brackets fall out of the jumper block. Unfortunately there is no reference in the Sonnet documentation, it is only mentioned that a jumper is...
  11. M

    Identification RasterOps cards for SE/30 PDS

    You‘re right, didn‘t see that printing. Sorry and thank you!
  12. M

    Identification RasterOps cards for SE/30 PDS

    Hello, I found these two RasterOps cards in SE/30 macs. The upper one is the ColorBoard 264/SE30, but what about the other one? Does anybody now which card that is? Has one connector and goes to the backside with DB15 port (same as the 264/SE30) Thanks
  13. M

    Macintosh ROM, 64-pin SIMM

    Thanks for your feedback, I´ll try that and see how it works
  14. M

    Macintosh ROM, 64-pin SIMM

    Hello, I´ve a question about the 64pin ROM SIMM which Apple used in the IIx, IIfx, IIsi, IIcx, IIci and SE/30. Are they interchangeable on these models (even if they have different ROM sizes and some of them are 32-bit clean)? There are ROM SIMMs with different part no. (eg. 341-0655A...
  15. M

    Macintosh SE/30 logicboard recreation (thread revival)

    Very nice to see that other people are working on the same project. Did you order the green PCB from JLCPCB with the backside already presoldered? If so, would you share a picture please? I´m not sure if should order five naked blue boards or five with backside pres. You did a good solder job...
Top