Home
Forums
New posts
Search forums
Wiki
What's new
New posts
New media
New media comments
New resources
New profile posts
Latest activity
Media
New media
New comments
Search media
Resources
Latest reviews
Search resources
Members
Current visitors
New profile posts
Search profile posts
Snitz Archive
Patreon
Log in
Register
What's new
Search
Search
Search titles only
By:
Current visitors
New profile posts
Search profile posts
Menu
Log in
Register
Install the app
Install
Updated 2023-07-12: Hello, Guest! Welcome back, and be sure to check out
this
follow-up post about our outage a week or so ago.
Home
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Callan's latest activity
Callan
replied to the thread
How to fix this distortion on the display? Picture inside.
.
The neck board just supplies the grid, heater, and gun. It won't effect the geometry of the tube. Also before any yoke adjustments let...
Mar 24, 2024
Callan
replied to the thread
How to fix this distortion on the display? Picture inside.
.
Sorry. Just noticed that. I would try to push the yoke a little closer to the tube if you can (with the power off) and see if it will...
Mar 24, 2024
Callan
replied to the thread
How to fix this distortion on the display? Picture inside.
.
There are some magnets on the yoke that adjust the geometry of the tube. I would assume snce the top right is out if alignment you'll...
Mar 24, 2024
Callan
replied to the thread
Acquired a IIfx (yay!) Issues (boo!)
.
Probably a little above mine too, but just to check.How is the 5v on other places on the board? Is it just low at the floppy drive? Are...
Mar 23, 2024
Callan
replied to the thread
Acquired a IIfx (yay!) Issues (boo!)
.
Your welcome! Yeah. I would replace all the electrolytics (power supply and motherboard). Only reason i said the motherboard first is...
Mar 22, 2024
Callan
replied to the thread
Acquired a IIfx (yay!) Issues (boo!)
.
Don't know much about the iifx. Saying that.... it sounds like everything else is working except the floppy's 5v. I know everyone says...
Mar 22, 2024
Callan
replied to the thread
Apple IIe Resistor
.
That's just a dcap (not a resistor) . That wouldn't prevent it from booting. Most issues I've found with 2e's have been ram related (4164's)
Mar 21, 2024
Callan
replied to the thread
LCIII Recap - Apple design fault -47uF reversed!
.
I can confirm you have to change the polarity of c22. It's -5 rail and for some reason the mask has you putting it on backwards. They...
Mar 9, 2024
Callan
replied to the thread
IIGS high speed scsi
.
Congrats! It's a must have for the IIGS! That and a Bluescsi (or your favorite - zigzagjoe's tinyscsi is amazing too!) makes loading...
Mar 9, 2024
Callan
reacted to
halkyardo's status
with
Like
.
SEthernet/30 cards all made up and ready to go out to beta testers this week!
Mar 6, 2024
Callan
replied to the thread
SE/30 subject to analog board recap but decided not to...
.
You can confirm that by just tugging (lightly) on the anode wire (with the machine off, obviously). You will feel the resistence from...
Mar 3, 2024
Callan
replied to the thread
SE/30 subject to analog board recap but decided not to...
.
Yeah. It sounds like you didn't plug the yoke back in correctly, or you might have fractured solder joints the connector. It's a 4 pin...
Mar 2, 2024
Callan
replied to the thread
SE/30 Focus Control?
.
I would make sure you haven't bent any pins on your tube / check you neck board. Also check for cracked joints on the connectors header...
Feb 24, 2024
Callan
replied to the thread
My GS died today
.
Input to the adb will be high. The adb will then trigger reset low for everything else.
Feb 22, 2024
Callan
replied to the thread
My GS died today
.
Looks like it's at the ADB chip. The RC circuit at tp74 does the initial reset on powerup (thanks robespierre). The ADB also handles...
Feb 22, 2024
Home
Members
Top