Search results

I'm sorry to confuse you with the broad strokes. Those 3 chips were corroded with cap goo and the corrosion was repaired. And I visually saw that the circuit leading from the ROM chip to the vicinity of those 3 chips were disconnected by the cap goo, so I repaired that. I wrote that it may not...

I have also repaired an IICI with the same problem. It was caused by cap goo that had broken the pattern from the UB13, UD13, and UE13 chips to the ROM chip. It is highly possible that it is not the exact same problem, but you might want to check the connections in that area by referring to the...

I found it in Aliexpress.

Bolle didn’t reply. So, I try to repair myself. Carrera’s FPGA chips were very hot. Then, they must be broke(I believe). I bought FPGA Chips, and changed them using heat gun. Pin header was melt down, but Carrera 040 come back to life!

Thanks, I will try it.

I think so. well I don’t know how to contact him.

I bought an original Carrera 040. But, that card's capacitor was still removed. So,I soldered capacitor, and put into IICi. Then, I turned on IICi, so led and fan was working, but didn't chime,didn't boot. Monitor was showed white display,no arrow. I'm tring to fix now, so plese help me. C27's...

どうもありがとう！ 未知のカードの意味がわかり ました。 しかし、互換性のあるモニターを持っていません。 別の使用可能なモニターを検索してみます。

I try to put this card in a IICi. At first, IICi can show video, but monitor turn gray. It maybe, unknown card was main monitor (when I puted into vga card into SE, same phenomenon was happened). So, I connected vga cable to unknown card, then, moniter turn black ,HDD is moving. Unknown card...

Thanks everyone. If your information is true, I have no idea for use. This card has D-Sub 9-pin plug. If this card is video card, I can use it, so I hope so.

Hi everyone. I need help. I got this huge Nubus card. At first, I thought that was VGA card. But, I can’t get any information. Please help me.

If you can cut SE/30’s Shell, you can use it. When you want to inject floppy into Manual-inject drive, you need to push by your finger. But normal SE/30's shell can’t reach to inject. You need to cut the SE/30’s shell. And if you want to use mechanical emergency eject button, you need to make...

Hi , SE/30’s floppy drive is MP-F75W-xxG. It is auto-inject drive. But 6100’s floppy drive is MPF xxA or MF355F-xxMA. It is manual-inject drive. They are not same, so you can’t use. I will paste the link of the detailed page. https://siber-sonic.com/mac/superfloppy.html

Maybe it is ColorBoard108+ / 30. I found that letter near the Nubus slot.

Hello everyone. My SE/30 is back! UD8 to A0 pattern was disconnected, so I bypassed to UE10. Then, SE/30's screen was clear. Thank you very much!

Thanks. I will try it!

Thanks. Maybe, 2nd advice is right. Because, I have another VRAM chip, and I changed before. But didn’t change state. I checked these connections before, but the situation was changed. So, I will try it again.

Hello everyone. I don't give up yet. And there was a change in the situation. I clean up ROM SIMM's terminal and slot carefully . Then, SE/30's screen shake was gone! :) But, SE/30's screen got stripe line. image2 is that state. I cleaned up around video logic,but did not change state. So, I...

Hello everyone, nice to meet you. I got a bad Macintosh SE/30. At first, it had no chime, but OS was run. And The screen has like checkered pattern. First image is that state. So, I recaped logic board. SE/30 got chime, but screen didn`t change. I tried to wash logic board. Then chime add...