Search results

To match it, you’d have to use a PDS card instead of NuBus…

I'm pretty sure that's only if you sell it; and mark it with the registered trademarks. However - I am not a lawyer, nor do I play one on TV, etc, etc... But in this case; it's most definitely NOT an HDMI connection - that would require adherence to HDCP, etc - it's just a DVI signal being sent...

There wasn't. It's just the 128k/512k/512ke/Plus keyboard and mouse connectors.

FWIW, on my other machine (2015 i7 iMac) I've got a linux-based VM that runs Xilinx ISE... although I haven't tested programming an XC9500 series chip with it yet. It's based off of the VM that Xilinx was distributing for running ISE under Windows 10. IIRC, it runs in VirtualBox.

I remember being at Macworld when these first came out, seeing it run - and really wanting one badly, but knowing that there was no way I was going to be able to get the budget for that. IIRC, the initial multiprocessing services manager that Apple shipped with the OS was licensed from Daystar...

OK, I'm back and have had a chance to read the thread. It looks like it's not quite as bad as I had thought; however I'd still use a CPLD to manage the low-level bus interface - it's just not that hard of a thing to integrate, compared to what it gives you. From Designing Cards and Drivers...

I haven't had a chance to fully read the thread since I made the post - and I'm on my way out the door right now - so I'll have more to say about it later; but... I am making the presumption that the MCU will service interrupts other than the bus interface interrupt; which will totally kill any...

A Microcontroller won't have the performance needed for a direct CPU-bus interface. You'll need to use a CPLD and some discrete logic at a minimum; but adding a FPGA to the mix would really help matters. The XC9500 series CPLD is 5V tolerant but runs at 3.3v; and is available in QFP packaging...

What I had in mind was to completely replace all of the circuits on the Analog Board - HV drive for the CRT's anode & cathode; sweep, blanking, etc. What I'm looking for datasheet-wise is something that gives a) the pinouts of the CRT; and b) the voltages and currents required.

No, I don't - hence the question. I'm wondering if the old Sam's Photofact sets might have something in it?

The other possibility is to cut the resolution in half in both directions 1920x1080 becomes 960x540; and just have the FPGA do the pixel doubling so the 68k processor only sees the lower resolution.

If we could find the data sheets for the CRTs themselves, we could design a driver board that uses all modern general purpose parts - a microcontroller to generate the requisite waveforms; voltage multipliers to drive the high voltage for the tube itself, etc…

In principle, a board could be designed to interface a PC 5.25 drive to SCSI - perhaps based off the BlueSCSI project. You'd then have to write a driver for the Mac to read it. AdaFruit has recently done some work interfacing floppy drives to their CircuitPython boards... so resources are out...

Uhh... shouldn't the frame rate be tied to the 60hz vertical blanking interrupt?

Hey - at least you don't have wildlife jumping out in front of you while you're driving back from said storage units!

Slap some PV panels on your roof and quit worrying about it. ;) (seriously - the emissions from just changing your driving style a little bit absolutely dwarf what a computer uses. 1 Horsepower = 0.7457 kW)

What to use it for? Marathon, of course!

It is a hard-learned truth that the fewer lines of code you have, the better off you are: that's code that you don't have to maintain... and that applies to everything from tiny microcontrollers to classic computers to large systems running on modern hardware. So, yeah - prune it down to the...

I sprung the $$$ for the compiling service at www.gryphel.com... I can only presume whatever warnings the complier may be throwing are getting tossed into /dev/null....

I've found that sometimes 70% isopropyl won't work for some stuff - I have to use 99%; because what the other 30% is made of in 70% isopropyl is water; and some stuff is very hydrophobic.